This page was exported from Latest Lead2pass Dumps For Sharing [ https://www.ensurepass.net ] Export date:Sat Dec 21 12:44:51 2024 / +0000 GMT ___________________________________________________ Title: [2017 New] 300-115 Exam Dumps Free Download In Lead2pass 100% 300-115 Exam Questions (251-275) --------------------------------------------------- 2017 August Cisco Official New Released 300-115 Dumps in Lead2pass.com! 100% Free Download! 100% Pass Guaranteed! Thank you so much Lead2pass. You helped me passing my 300-115 exam easily, 90% of the exam questions from the dump appeared in my exam. Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-115.html QUESTION 251What is cisco recommendation for RSPAN best practice? A.    you should configure remote vlan firstB.    use different vlan for multiple/different switchesC.    use different portchannelAnswer: A QUESTION 252What is needed for Virtual Switching System "VSS"? A.    portchannelB.    trunkC.    Virtual Switching Link "or VSL" Answer: C QUESTION 253Which will identify the master switch in stack wise? A.    lower priorityB.    higher priorityC.    lower idD.    higher id Answer: B QUESTION 254What happens if you apply this command "vlan dot1q tag native" ? A.    packet will be droppedB.    packet go to defautl vlanC.    packet go to native vlan Answer: C QUESTION 255A Switch has been configured with the Vlan dot1q tag native command. Which statement describes what the switch does with untagged frames that it receives on a trunked interface A.    Untagged frames are forwarded via the default VLANB.    it drops the untagged framesC.    The trunked port is put in err-disabled stateD.    Untagged frames are forwarded via the native VLAN Answer: D QUESTION 256An engineer is configuring an EtherChannel between two switches using PAgP If the EtherChannel mode on switch 1 is configured to auto, which modes on switch 2 establish an operational EtherChannel? A.    activeB.    autoC.    desirableD.    onE.    passive Answer: C QUESTION 257switch#show standbyVirtual IP address is X.X.X.XHello time 3 sec, hold time 10 secPreemption disabledActive router is X.X.X.3 priority 85Standby router is localPriority 90 (configured 90)Track interface faX/X state decrement 10 (Choose two) A.    The link will take over when .....B.    X.X.X.3 is active becuse it has higher IP addressC.    when faX/x is down praiority will be 80D.    it is using default hello and hold values Answer: CD QUESTION 258Question about trunk configurationint faX/Xswitchport trunk allowed vlan x,x,x,xswitchport mode trunkexitshow vlanVLAN Name Status Ports--- --------------------?------ ---------------------1 default active Fa0/1, Fa0/3, Fa0/3, FaX/Xshow interface trunk(no output) A.    link is shutdownB.    interface needs no shutdownC.    other side is configured as access portD.    missing switchport command Answer: A QUESTION 259What happens spoofed packet or something like untrusted packet is detected? (Choose three) A.    logB.    deletesC.    interceptsD.    acceptsE.    discad Answer: ACE QUESTION 260Refer to the exhibit. An engineer is configuring an etherchannel between two switches, he notices the error message on Switch 2 (error message channel-missconfiguring error), based on the output what is the problem? A.    the etherchannel on the switch 1 using incorrect member portB.    the etherchannel interface of switch 1 is not configuredC.    the etherchannel protocol on switch 1 is not correctD.    the etherchannel interface of switch 2 is not configured Answer: C QUESTION 261Drag and Drop Question A.    See the exhibit Answer: A QUESTION 262Drag and Drop Question   A.    See the exhibit Answer: A QUESTION 263When using EtherChannel misconfiguration guard, which technology is used to prevent this type of misconfiguration from affecting the network? A.    LACPB.    port securityC.    STPD.    PAgP Answer: A QUESTION 264What is the Ethernet frame size for 802.1Q? A.    64B.    128C.    1518D.    1522 Answer: D QUESTION 265How will the traffic reach the core switch from AS switch to DS core switch?(Based on a topology shown with one core, two distribution and two access switches on each distribution switch, with redundant links and bandwidth mentioned.) A.    ASW1 to DWS1 to coreB.    ASW1 to DWS2 to core Answer: B QUESTION 266If HSRP group number is 45 what would be the MAC address?(Basically conversion of digit to hexadecimal with group of 16.) A.    00-00-0c-07-ac-2D Answer: AExplanation:00-00-0c- 07-ac-2DCISCO_ID :HSRP_ID:GROUP_ID2d=45 QUESTION 267EtherChannel guard misconfig is configured on a switch, which technology supports that? A.    LACPB.    PagPC.    STPD.    Port Security Answer: C QUESTION 268Select a valid VRRP configuration from a list of possible configurations. A.    vrrp [group-number] ip [ip-address]B.    vrrp [group-number] priority [priority]C.    vrrp [group-number] preempt Answer: ABCExplanation:You can eliminate configurations with the word `standby', as that would be HSRP, not VRRP. Also, I think the options that put things like vrrp group 1 ip x.x.x.x are wrong. You don't need the word `group' in the configuration line. The number 1 is the group number. Anyway, just take a good look a t a few valid VRRP configuration examples so that you will be able to recognize invalid ones. QUESTION 269Private VLANs (PVLANs) have two secondary VLAN types. A.    communityB.    isolated Answer: AB QUESTION 270What types of SDM templates you can use in switch? (Choose four) A.    AccessB.    DefaultC.    RoutingD.    VLANs Answer: ABCDExplanation:+ Access - The access template maximizes system resources for access control lists (ACLs) to accommodate a large number of ACLs.+ Default - The default template gives balance to all functions.+ Routing - The routing template maximizes system resources for IPv4 unicast routing, typically required for a router or aggregator in the center of a network.+ VLANs - The VLAN template disables routing and supports the maximum number of unicast MAC addresses. It would typically be selected for a Layer 2 switch. QUESTION 271What is the process to configure EtherChannel? A.    shutdown both interface portsB.    shutdown the interface on one side only Answer: A QUESTION 272A question about spanning-tree port-priority. A.    128B.    129 Answer: A QUESTION 273Spanning-tree EtherChannel misconfiguration A.    (config)#spanning-tree etherchannel guard misconfigB.    (config-if)#spanning-tree etherchannel guard misconfig Answer: A QUESTION 274There was another Exhibit about port priority- Core switch connected to 2 dis switches which connected 2 ASW. PC1 is connected to DSW1 and DSW2 (Root Bridge). Link connected from PC1 to DSW2 is 4Gbps and DSW1 is 10Gbps. There is etherchannel trunk between DSW1 and DSW2. Default port prioirty is configured. Change in port priority so traffic goes through DSW1 to DSW2 A.    DSW1: spanning-tree port priority 16B.    DSW1: interface g1/0C.    DSW2: spanning-tree port priority 16D.    DSW2: interface g1/0E.    DSW1: spanning-tree port priority 0 Answer: AB QUESTION 275If EtherChannel guard is configured, how the interface status is (or looks like) if misconfigured? A.    errdisabledB.    shutdown Answer: A Suggestion, read 300-115 questions carefully try to understand or guess what they're asking for. Hope everyone passes. 300-115 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDUFIySDhBLWlPcmc 2017 Cisco 300-115 exam dumps (All 401 Q&As) from Lead2pass: https://www.lead2pass.com/300-115.html [100% Exam Pass Guaranteed] --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2017-08-01 03:35:38 Post date GMT: 2017-08-01 03:35:38 Post modified date: 2017-08-01 03:35:38 Post modified date GMT: 2017-08-01 03:35:38 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com